News

Ball screw nuts are usually used in combine with ball screws, it is widely used in high precision machinery and automation equipment. Learning how to install and maintain ball screw nut becomes very important for everyone who works on CNC machining centers.

1. Cleaning:

Ensure that the installation environment is clean and prevent dust and impurities from entering the ball screw nut.

Before installation the ball screw nut,  keep the ball screw and other parts should be cleaned to remove anti-rust grease and other protective coatings.

Inspection:

Check whether the ball screw and its accessories (such as nuts, bearings, and support seats) are good.

2. Mounting base

The mounting base should have sufficient rigidity to ensure that the ball screw does not deform during operation.

Parallelism and straightness:

Ensure that the parallelism and straightness of the mounting base meet the design requirements.

3. Mounting nut

Preload: 

The preload of the ball screw nut should be appropriate, ensuring that it is in close contact, but not too tight to prevent excessive friction.

The adjustment of preload force should be carried out according to the specific requirements of the equipment and the specifications of the ball screw.

Lubrication:

When installing the nut, ensure good lubrication, use appropriate lubricating oil or grease, and avoid dry friction.

4. Testing

Manual debugging: 

After installation, perform manual debugging, slowly turn the ball screw, and check whether it runs smoothly and whether there is any jamming.

Dynamic test:

Perform dynamic test, drive the ball screw through the drive motor, and observe its running status.

Check whether there is any abnormal noise, vibration or overheating during operation.

5. Maintenance after installation

Regular lubrication:

Regularly check the lubrication of the ball screw to ensure that the lubricating oil or grease is sufficient.

Develop a reasonable lubrication maintenance plan based on the usage and working environment.

Cleaning:

Regularly clean the ball screw and its surrounding environment to prevent dust and impurities from entering.

Check wear:

Regularly check the wear of the ball screw. If severe wear is found, it should be replaced in time.

The installation of ball screws requires precise centering, reasonable preload and good lubrication to ensure that they remain stable, efficient and have a long life during operation. Attention should be paid to every detail during the installation process to avoid performance degradation or equipment damage caused by improper installation. Regular maintenance is also important to extend the service life of the ball screw and ensure its stable operation.

How to repair the ball screw nut:

1. The screw nut must be perpendicular to the screw axis during installation and lubricant should be added appropriately. During use, care should be taken to prevent external dust and debris from entering, causing blockage and wear

2. For screw nuts that have been installed and put into use, regular inspection and maintenance are also important means to extend their service life. Lubricants should be cleaned and replaced regularly to prevent excessive wear and rust. In addition, parameters such as nut bearings, load capacity, friction, etc. should be checked regularly to promptly identify possible problems and deal with them.

3. Reasonable use of screw nuts is also an important factor in ensuring their service life. A reasonable use plan should be formulated and strictly implemented, and overload should not be used at will to avoid wear and looseness.

4. When buying screw nuts, you should choose high-quality brands produced by regular manufacturers and try to avoid buying low-priced and low-quality products. At the same time, different types of screw nuts should be selected to meet different requirements in different mechanical applications.

5. During the use of screw nuts, sometimes they cannot be repaired due to bearing damage, looseness and deformation. At this time, they should be replaced in time to avoid continued use and harm.

Correct installation, reasonable maintenance, reasonable use, selection of high-quality screw nut brands and timely replacement are all effective ways to extend the service life of screw nuts. Only by following these methods can we ensure that the screw nuts can maintain efficient operation for a long time.

RicoCNC can offer a sereis of famous brand ball screew nut, Rexroth FEM-E-C, FEM-E-S, FEM-E-B, SEM-E-S, SEM-E-C, ZEM-E-S, ZEV-E-S, FDM-E-S, FDM-E-B, with quality assurance. Welcome to your inquiry.